Cooper M3000 Uživatelská příručka Strana 1

SPARC Enterprise M3000/M4000/M5000/M8000/M9000 ServersXSCF User's GuidePart No.: 821-2797-10, Manual Code: C120-E332-10ENDecember 2010, Revision

x SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010A. Warning and Information Messages A–1A.1 Message Types A–1A.2 Messages in Each Fun

2-60 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showad(8) command to confirm that the server certificate is loaded.4.

Chapter 2 Setting Up XSCF 2-61Setting a user domain Command operation1. Use the showad(8) command to display user domains.2. Use the setad(8) command

2-62 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setad(8) command to set default roles.3. Use the showad(8) command to

Chapter 2 Setting Up XSCF 2-63Setting Group name and privileges Command operation1. Use the showad(8) command to display the group name.<Example1&

2-64 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setad(8) command to set group name and privileges.<Example1> Set

Chapter 2 Setting Up XSCF 2-653. Use the showad(8) command to confirm the group name and privileges.<Example1> Confirm administrator group.XSCF&

2-66 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The administrator group has platadm, useradm, and auditadm privileges and you can

Chapter 2 Setting Up XSCF 2-67Enabling or Disabling the Logging of Active Directory Authentication and Authorization Diagnostic Messages Command oper

2-68 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the showad(8) command to display the diagnostic messages.3. Use the setad(

Chapter 2 Setting Up XSCF 2-693. Use the showad(8) command to confirm the defaut settings.XSCF> showaddnslocatormode: disabledexpsearchmode: disabl

Preface xiPrefaceThis manual describes the system monitor and control facility, known as eXtended System Control Facility (XSCF), which is used to con

2-70 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.5 LDAP/SSL AdministrationLDAP/SSL administration is used to specify items rel

Chapter 2 Setting Up XSCF 2-71TABLE 2-10 lists setting items and the corresponding shell commands:TABLE 2-10 LDAP/SSL AdministrationItem Description

2-72 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Display userdomainDisplays the userdomain. showldapsslUserdomain Configures up to

Chapter 2 Setting Up XSCF 2-73Before LDAP/SSL settingsNote the following before settings: LDAP/SSL is supported in XCP1091 or later. The useradm pri

2-74 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showldapssl(8) command to confirm the use of LDAP/SSL server.Specifyin

Chapter 2 Setting Up XSCF 2-753. Use the showldapssl(8) command to confirm the LDAP/SSL server setting.Enabling or Disabling the Usermapmode Command

2-76 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showldapssl(8) command to confirm the usermapmode status.Configuring o

Chapter 2 Setting Up XSCF 2-774. Use the setldapssl(8) command to clear the usermap.5. Use the showldapssl(8) command to confirm that the usermap is c

2-78 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showldapssl(8) command to confirm the strictcertmode status.If strictc

Chapter 2 Setting Up XSCF 2-79Loading or Deleting the Server Certificate Command operation1. Use the showldapssl(8) command to display the server cer

xii SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010AudienceThis guide is written for experienced system administrators with working k

2-80 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setldapssl(8) command to load the server certificate to the XSCF.<E

Chapter 2 Setting Up XSCF 2-813. Use the showldapssl(8) command to confirm that the server certificate is loaded.4. Use the setldapssl(8) command to d

2-82 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Setting a user domain Command operation1. Use the showldapssl(8) command to disp

Chapter 2 Setting Up XSCF 2-833. Use the showldapssl(8) command to confirm the default roles.XSCF> showldapssl defaultroleDefault role: platadm pla

2-84 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Setting Group name and privileges Command operation1. Use the showldapssl(8) com

Chapter 2 Setting Up XSCF 2-852. Use the setldapssl(8) command to set group name and privileges.<Example1> Sets administrator group 1.XSCF> s

2-86 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showldapssl(8) command to confirm the group name and privileges.<Ex

Chapter 2 Setting Up XSCF 2-87The administrator group has platadm, useradm, and auditadm privileges and you cannot change that. Also the operator grou

2-88 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setldapssl(8) command to set the log detail level.3. Use the showldaps

Chapter 2 Setting Up XSCF 2-89Change the LDAP/SSL Settings Back to the Default Command operation1. Use the showldapssl(8) command to display the LDAP

Preface xiiiSPARC Enterprise M4000/M5000 Servers Safety and Compliance Guide 819-2203 C120-E348SPARC Enterprise M8000/M9000 Servers Safety and Complia

2-90 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.6 Time AdministrationTime administration is used to specify the time and the

Chapter 2 Setting Up XSCF 2-91TABLE 2-11 lists the settings and the corresponding shell commands.TABLE 2-11 Setting Time and DateItem Description She

2-92 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Specifying a Time Zone Command operation1. Use the showtimezone(8) command to di

Chapter 2 Setting Up XSCF 2-93Specifying a Daylight Saving Time Command operation1. Use the showtimezone(8) command to display the time zone.2. Use t

2-94 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Setting the XSCF Time Command operation1. Use the showdate(8) command to display

Chapter 2 Setting Up XSCF 2-95Configuring an NTP Server Command operation1. Use the showntp(8) command to display the NTP server for the XSCF network

2-96 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105. Use the showntp(8) command to confirm the NTP server. Specifying or Canceling

Chapter 2 Setting Up XSCF 2-97Changing Stratum Value for XSCF Command operation1. Use the showntp(8) command to display the stratum value for the XSC

2-98 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setntp(8) command to change a clock address of the XSCF's own loc

Chapter 2 Setting Up XSCF 2-99Of the two NTP server outputs, the upper (192.168.1.2) indicates the NTP server which is set by using the setntp(8) comm

xiv SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Text ConventionsThis manual uses the following fonts and symbols to express specif

2-100 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010specifying either from 1 to 3, the address of an NTP server which is referring t

Chapter 2 Setting Up XSCF 2-1015. Use the poweron(8) command to turn on power to all domains.6. Use the showdateoffset(8) command to confirm no differ

2-102 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010SSH ClientIn this system, you can use the following SSH clients. Oracle Solaris

Chapter 2 Setting Up XSCF 2-103To enable the SSH, to set the SSH access control from domain, and to disable the telnet, the XSCF reset is required. Pl

2-104 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling SSH/Telnet Command operation1. Use the showssh(8) command

Chapter 2 Setting Up XSCF 2-105Permitting or Refusing the SSH Access to XSCF from Domain via DSCP Command operation1. Use the showssh(8) command to d

2-106 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Specifying an SSH Host Key Command operation1. Use the showssh(8) command to di

Chapter 2 Setting Up XSCF 2-107Specifying the Timeout Period of SSH/Telnet Command operation1. Use the showlogout(8) command to display the timeout p

2-108 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104. Use the showssh(8) command to confirm the user public key and its number. Do

Chapter 2 Setting Up XSCF 2-1092.2.8 Https AdministrationUse https administration to specify the settings required for operating the web browser windo

Preface xvSyntax of the Command-Line Interface (CLI)The command syntax is as follows: A variable that requires input of a value must be put in Italic

2-110 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105. Enable https.For Step 1 - Step 5 above, specify each option using the sethttp

Chapter 2 Setting Up XSCF 2-111To enable the https, an XSCF reset is required. Please reset the XSCF using by rebootxscf(8) command. After the XSCF re

2-112 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling Https Command operation1. Use the showhttp(8) or the show

Chapter 2 Setting Up XSCF 2-1133. To enable the https, the XSCF reset is required. Use the rebootxscf(8) command to reset the XSCF. After the XSCF re

2-114 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104. Send the copied CSR to the CA and request the web server certificate. 5. Perf

Chapter 2 Setting Up XSCF 2-115Creating a Web Server Certificate by Constructing the Self CA Command operation1. Use the sethttps(8) command to creat

2-116 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.9 Audit AdministrationAudit administration is used to specify logging of acc

Chapter 2 Setting Up XSCF 2-117TABLE 2-17 lists the setting items and the corresponding shell commands.Audit trail Set of audit files. The user refers

2-118 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – (1) If audit is disabled, writing to the audit trail is stopped, all requ

Chapter 2 Setting Up XSCF 2-119If the audit trail becomes full while count is the specified policy, new audit trail data is discarded, and the number

xvi SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

2-120 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling Audit, Transferring a Log File, and Deleting Audit Data C

Chapter 2 Setting Up XSCF 2-121Specifying the Audit Policy Command operation1. Use the showaudit(8) command to display the audit policy.2. Use the se

2-122 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showaudit(8) command to confirm the setting.Displaying the Audit Logs

Chapter 2 Setting Up XSCF 2-1232.2.10 Log Archiving AdministrationThis section explains how to set the log archiving function, which saves the logs re

2-124 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – For the types of logs that can be saved, see Chapter 8.Note – When you se

Chapter 2 Setting Up XSCF 2-125Specifying a Host Name, Directory Name, Login User Name and Password for the Target of Log Archiving, and Enabling or D

2-126 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104. Use the showarchiving(8) command to confirm the settings.Specifying the Host

Chapter 2 Setting Up XSCF 2-127Setting Capacity Limits for the Log Archiving Function Command operation1. Use the showarchiving(8) command to display

2-128 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Displaying Log Archiving Error Information Command operation● Use the showarch

Chapter 2 Setting Up XSCF 2-129TABLE 2-21 lists settings and the corresponding shell commands.VACM Abbreviation for View-based Access Control Model. T

1-1CHAPTER1XSCF OverviewThis chapter provides an overview of the system monitoring and control facility (eXtended System Control Facility, or XSCF).1.

2-130 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010SNMPv3 trap Makes the following SNMPv3 trap settings:• User name (Note 1)• Auth

Chapter 2 Setting Up XSCF 2-131Note – (1) A user name, authentication password, and encryption password that are common to both the sending and receiv

2-132 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Setting the SNMP Agent’s System Management Information and Enabling/Disabling th

Chapter 2 Setting Up XSCF 2-133Setting SNMPv3 Trap Command operation1. Use the showsnmp(8) command to display SNMP settings.2. Use the setsnmp(8) co

2-134 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Confirm the SNMPv3 trap settings.Disabling Traps to the Target Host of SNMPv3

Chapter 2 Setting Up XSCF 2-135Enabling/Disabling the SNMPv1 and SNMPv2c Communication Command operation1. Use the showsnmp(8) command to display S

2-136 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Disabling Traps to the Target Host of SNMPv1/SNMPv2c Command operation1. Use

Chapter 2 Setting Up XSCF 2-1375. Confirm the SNMP settings. Note – When you changed the SNMP settings back to the default, if the Sun Management Cent

2-138 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showsnmpusm(8) command to display USM management information.Creatin

Chapter 2 Setting Up XSCF 2-1392. Use the setsnmpvacm(8) command to set VACM management information.3. Use the showsnmpvacm(8) command to confirm the

1-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – (1) Processors on server boards are called CPUs.Note – (2) Only the system

2-140 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 2-22 lists the settings and the corresponding shell commands.TABLE 2-22 M

Chapter 2 Setting Up XSCF 2-141Specifying the Host Name, Port Number, and Reply Address of the SMTP Server Command operation1. Use the showsmtp(8) c

2-142 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling the Mail Report Function and Specifying the Recipient Addr

Chapter 2 Setting Up XSCF 2-143In the M3000 server, you cannot perform the operations such as setting the domain configuration, or adding or deleting

2-144 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Domain ConfigurationDivides hardware resources in this system into independent s

Chapter 2 Setting Up XSCF 2-145Note – (1) DR: Abbreviation for Dynamic Reconfiguration. This function dynamically adds a system board to a domain or d

2-146 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – Enabling Memory Mirror would require twice the amount of memory of a doma

Chapter 2 Setting Up XSCF 2-147One domain can use up to 16 LSBs. The user can define the different XSB in each LSB by using XSCF. Also, multiple domai

2-148 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Caution – IMPORTANT - If the XSB associated with the specified LSB has been conf

Chapter 2 Setting Up XSCF 2-149Note – The result of the initial diagnosis by testsb(8) command is displayed in specified PSB. Also you can use the sho

Chapter 1 XSCF Overview 1-3 Remote Cabinet Interface (RCI) port to perform power supply interlock by connecting a system and an I/O device with an RC

2-150 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Domain Hardware and Software ConfigurationsFIGURE 2-2 lists the hardware resourc

Chapter 2 Setting Up XSCF 2-151FIGURE 2-3 XSCF-Domain Correlation DiagramDomain modulesXSCF modulesXSCF-Domain networkDSCP InterfaceXSCF-Domain Comma

2-152 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 2-4 and FIGURE 2-5 show XSB hardware configuration diagrams in the midran

Chapter 2 Setting Up XSCF 2-153FIGURE 2-5 XSB Configuration Diagram (Quad-XSB) (In the Midrange Servers)When PSB#n is Quad-XSB typeCMU IOUXSB#00-2XSB

2-154 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 2-6 and FIGURE 2-7 show XSB hardware configuration diagrams in the high-e

Chapter 2 Setting Up XSCF 2-155FIGURE 2-7 shows Quad-XSB hardware configuration diagrams in high-end servers.FIGURE 2-7 XSB Configuration Diagram (Qu

2-156 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 2-8 shows Uni-XSB hardware configuration diagrams in an entry-level serve

Chapter 2 Setting Up XSCF 2-157Note – For the procedure for installing, removing, or replacing a system board in the server, see the Service Manual fo

2-158 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – For details on using DR functions, see the Dynamic Reconfiguration User’s

Chapter 2 Setting Up XSCF 2-159Displaying the XSB StatusBy referring to the XSB status of a domain, the user obtains information about an XSB, such as

PleaseRecycleCopyright © 2007, 2010, FUJITSU LIMITED. All rights reserved. Oracle and/or its affiliates provided technical input and review on portion

1-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 1-1 Outline Drawing of the Rear Panel (In the Entry-level Server)RCI PortW

2-160 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Displaying or Specifying DCL Information Command operation1. Use the showdcl(8)

Chapter 2 Setting Up XSCF 2-1613. Use the showdcl(8) command to display DCL information.XSCF> showdcl -va DID LSB XSB System No-Mem No-IO

2-162 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Assigning or Configuring a System Board to a Domain Command operation1. After t

Chapter 2 Setting Up XSCF 2-1633. Use the addboard(8) command to add an XSB and use the showboards(8) command to confirm the XSB status.4. Use the pow

2-164 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20106. Use the showboards(8) command to confirm the XSB status. (See TABLE 2-27.)7.

Chapter 2 Setting Up XSCF 2-165Deleting a System Board From a Domain Command operation1. Use the showdevices(8) command to display the usage of XSB r

2-166 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the showboards(8) command to display XSB status information.3. Use the po

Chapter 2 Setting Up XSCF 2-167Note – When you delete the system board, please confirm the domain status, the system board status, the device usage st

2-168 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showdcl(8) command to confirm the DCL information.4. Use the showboar

Chapter 2 Setting Up XSCF 2-1696. Use the showboards(8) command to discplay the XSB status again.7. Use the poweron(8) command to start up all domains

Chapter 1 XSCF Overview 1-5USB PortThe USB port (type A) is used to connect a USB device. The port is compatible with USB 1.1. The port can be used by

2-170 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.14 System Board ConfigurationSystem board configuration settings are used to

Chapter 2 Setting Up XSCF 2-171Note – (1) Memory mirroring requires twice the amount of memory domain used for operation. If the PSB is a Quad-XSB typ

2-172 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showfru(8) command to display information on dividing a PSB into XSBs

Chapter 2 Setting Up XSCF 2-1734. Use the testsb(8) command to check the PSB, then check the results by using the showboards(8) command.2.2.15 Domain

2-174 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 2-31 lists terms used in domain mode configuration.Note – When the mode sw

Chapter 2 Setting Up XSCF 2-175TABLE 2-32 lists setting items and the corresponding shell commands.Note – The display for domain ethernet address (mac

2-176 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The Status of the Mode Switch on Oracle Solaris OSWhen you execute the prtdiag(1

Chapter 2 Setting Up XSCF 2-177FIGURE 2-9 shows an example of a mixed configuration of SPARC64 VI and SPARC64 VII processors.FIGURE 2-9 CPUs on CPU/M

2-178 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010By default, the Oracle Solaris OS automatically sets a domain’s CPU operational

Chapter 2 Setting Up XSCF 2-179Note – Change the cpumode from auto to compatible for any domain that has or is expected to have SPARC64 VI processors.

1-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010administrators or FEs to configure the system settings, display the system status,

2-180 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setdomainmode(8) command to change the initial hardware diagnostic le

Chapter 2 Setting Up XSCF 2-1812. Use the setdomainmode(8) command to specify host watchdog and break signal suppression.3. Use the showdomainmode(8)

2-182 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setdomainmode(8) command to disable automatic boot.3. Use the showdom

Chapter 2 Setting Up XSCF 2-1833. Use the setdomainmode(8) command to set the CPU operational mode.4. Use the showdomainmode(8) command to confirm tha

2-184 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.16 Locale AdministrationLocale administration is used to set the XSCF Shell

Chapter 2 Setting Up XSCF 2-1852.2.17 Altitude AdministrationThis section explains the altitude settings. The server changes the system monitoring due

2-186 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.18 DVD Drive/Tape Drive Unit AdministrationDVD drive/tape drive unit configu

Chapter 2 Setting Up XSCF 2-187TABLE 2-38 lists the settings and the corresponding shell commands.Note – After the drive units are used for a domain (

2-188 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Changing the DVD Drive/Tape Drive Unit Settings Command operation1. Use the cfg

Chapter 2 Setting Up XSCF 2-1892.3 Save and Restore XSCF Configuration InformationTo save/restore the XSCF configuration information, execute the dump

Chapter 1 XSCF Overview 1-7FIGURE 1-2 Outline Drawing of the XSCF Unit Front Panel (In the Midrange Servers)The RCI port, serial port, USB port, XSCF

2-190 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 The head of the saved configuration file contains the following identification

Chapter 2 Setting Up XSCF 2-191Saving the Configuration Information to a Specified Target Directory Over a Network Command operation1. Perform the du

2-192 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – For more about encrypted data, see the man page or the XSCF Reference Man

3-1CHAPTER3Connecting to the XSCF and the ServerThis chapter describes how to connect consoles and terminals to XSCF in order to use the software, and

3-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103.1.1 Terminal Operating Modes for Connection to XSCFThe FIGURE 3-1 shows the term

Chapter 3 Connecting to the XSCF and the Server 3-3SerialThe XSCF Shell and domain console (OS console) can be used while a terminal is connected to a

3-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 3-1 lists the types of terminals connected to each port shown in FIGURE 3-1

Chapter 3 Connecting to the XSCF and the Server 3-5Note – A maximum of 20 users can be connected to the XSCF at the same time in the M3000/M4000/M5000

3-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 3-3 lists the port numbers used for the DSCP Link and the functions. When yo

Chapter 3 Connecting to the XSCF and the Server 3-73.1.4 Connecting to XSCF via the Serial PortThe following is the procedure for connecting to a term

1-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 1-3 Outline Drawing of the XSCF Unit Front Panel (In High-End Servers)The

3-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. On the PC or workstation to be used, use one of the following procedures: Conn

Chapter 3 Connecting to the XSCF and the Server 3-9Note – To start up the SSH client, see your SSH manual. For details on login, see Chapter 5. Conne

3-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 3-3 Example of Starting the Terminal Emulatora. To establish a telnet con

Chapter 3 Connecting to the XSCF and the Server 3-111. Perform the console(8) command on the XSCF Shell terminal screen to select the domain console.N

3-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 XSCF Shell XSCF Web SNMP agent function Mail notification function Time sy

Chapter 3 Connecting to the XSCF and the Server 3-13FIGURE 3-4 shows the intranet connection.FIGURE 3-4 Intranet Connection (In a High-End Server)Whe

3-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 3-5 shows the connection via an external network.FIGURE 3-5 Connection of

Chapter 3 Connecting to the XSCF and the Server 3-15XSCF Connection via a Serial PortEstablish an XSCF connection via a serial port. Connect the seria

3-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010If an error occurs in the active XSCF Unit in the systems with two XSCF Units, XS

Chapter 3 Connecting to the XSCF and the Server 3-17FIGURE 3-7 Example of LAN Port Connections Not Made RedundantUsing a Single LAN Port for Manageme

Chapter 1 XSCF Overview 1-9ACTIVE LEDThe ACTIVE LED lights up in green. If the XSCF Unit is in a redundant configuration, the ACTIVE LED indicates the

3-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 3-8 Example of a Connection With One LAN PortPort from XSCFU#0Port from X

4-1CHAPTER4Operation of the ServerThis chapter mainly describes operation of the server hardware.4.1 Display Server Hardware EnvironmentThis section d

4-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.1.1 Displaying System Information Command operation1. Use the showhardconf(8) c

Chapter 4 Operation of the Server 4-34. Use the showstatus(8) command to display information on degraded components in the system. (This screenshot is

4-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The M8000/M9000 servers do not indicate Middle speed. The M3000 server indicates m

Chapter 4 Operation of the Server 4-5Power consumption and Exhaust airTo display power consumption and exhaust air of a server, use the power consumpt

4-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010showenvironment command. For a power consumption value of the M4000/M5000/M8000/M9

Chapter 4 Operation of the Server 4-7In the M3000 server, the displayed information is CPU status, CPU operating frequency, CPU type, number of CPU co

4-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 XSCF Unit informationUnit number, status, version, serial number, and FRU number

Chapter 4 Operation of the Server 4-9Note – 8GB DIMM is supported in XCP1081 or later."Type" in the CPU/Memory board unit information is sup

1-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Initial System Configuration FunctionXSCF configures the initial hardware setting

4-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.2.1 Domain Information Command operation1. Use the showdcl(8) command to check

Chapter 4 Operation of the Server 4-113. Use the showboards(8) command to check the XSB number, domain ID, LSB number, and XSB status. 4. Use the vers

4-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010For details on adding or changing a domain, see Chapter 2 of the XSCF Reference M

Chapter 4 Operation of the Server 4-13 Warm-up time administration Dual power feed 4.4.1 System Power On Command operation1. Use the showlogs powe

4-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – Use the showdomainstatus(8) command to check the power status of the domai

Chapter 4 Operation of the Server 4-154. Use the showlogs power command to check the system power off.4.4.3 Domain Power On Command operation1. Use t

4-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.4.4 Domain Power Off Command operation1. Use the showdomainstatus(8) command t

Chapter 4 Operation of the Server 4-17Caution – IMPORTANT - See the following paragraphs for important information about the domain power-off procedur

4-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.4.6 Domain Reset Command operation1. Use the showdomainstatus(8) command to ch

Chapter 4 Operation of the Server 4-193. Use the showdomainstatus(8) command to check the power status of the domain specified to be reset.Note – When

Chapter 1 XSCF Overview 1-11 Automatically shut down and cancel a power on operation when an error is detectedIf a system abnormality occurs, the Ora

4-20 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Confirm ok prompt on the specified domain console.Note – To send the break sig

Chapter 4 Operation of the Server 4-214.4.9 Warm-Up Time AdministrationThe warm-up time is intended to prevent the power supply unit and the fan from

4-22 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Caution – IMPORTANT - When the power is turned on from the operator panel, the ai

Chapter 4 Operation of the Server 4-23 Command operation1. Use the showdualpowerfeed(8) command to display the current setting status of the dual pow

4-24 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.5 Identifying the Location of the SystemWhen more than one same type of system

Chapter 4 Operation of the Server 4-25 Command operation● Use the showstatus(8) command to display the unit status. An asterisk (*) is attached to a

4-26 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104.7 Changing the TimeThe time of the server is based on the XSCF time. Time can b

Chapter 4 Operation of the Server 4-27Caution – IMPORTANT - An XSCF reset or failover might prevet the above setting operation from completing. If a r

4-28 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 4-5 lists setting items and the corresponding shell commands.TABLE 4-5 Ext

Chapter 4 Operation of the Server 4-29Note – (1) Also called uplink cards. They are mounted on I/O boards.Note – (2) A locator LED that indicates a lo

1-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010number that can be referenced from the domain to the XSBs for control of the doma

4-30 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Displaying a List of External I/O Expansion Units, I/O Boards, Link Cards, and Po

Chapter 4 Operation of the Server 4-31Displaying and Setting the Locator LED State of Each Specified Component in an External I/O Expansion Unit Comm

4-32 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Displaying and Clearing the Card with ESM Command operation● Use the ioxadm(8) c

5-1CHAPTER5Overview of the XSCF ShellThis chapter describes how to use the XSCF Shell. The chapter also describes how to use commands and log in with

5-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 fieldeng: The user can perform the commands for FEs.TABLE 5-1 outlines the XSCF

Chapter 5 Overview of the XSCF Shell 5-3setpacketfilters Sets the IP packet filtering rules to be used in the XSCF network. showpacketfilters Displays

5-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010setupplatform • Sets up platform-specific settings.Note: In the platform-specific

Chapter 5 Overview of the XSCF Shell 5-5addboard Adds a system board to a domain. deleteboard Deletes a system board from a domain. Alternatively, it

5-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010reset Resets the specified domain. Note: The following three reset modes are avail

Chapter 5 Overview of the XSCF Shell 5-7Note – In the M3000/M4000/M5000/M8000/M9000 servers, some of the commands are not available, depending on the

Chapter 1 XSCF Overview 1-13Functions for Monitoring and Notification During OperationXSCF constantly monitors the system operating status, FAN status

5-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105.2.2 Operation From a Terminal Connected to the Serial PortThis section describes

Chapter 5 Overview of the XSCF Shell 5-9The following is a login example:When the SSH connection is done using a user key, install the user public key

5-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105.3 View Server Status and Control CommandsThis section describes the typical XSC

Chapter 5 Overview of the XSCF Shell 5-11fmadm / fmdump / fmstatThe server has an architecture that performs fault management (FMA) for CPUs, memory,

5-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105.4 Server Configuration Information CommandsThis section describes the typical X

Chapter 5 Overview of the XSCF Shell 5-13showstatusThe system administrator can use the showstatus(8) command to list degraded components. 5.5 Domain

5-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010showdcl / setdclThe showdcl(8) command displays the domain configuration informat

Chapter 5 Overview of the XSCF Shell 5-155.6 View and Archive the XSCF LogsThis section describes the XSCF commands that fetch and display server oper

5-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105.7 User Management and Security CommandsThis section describes the typical XSCF

Chapter 5 Overview of the XSCF Shell 5-17showaudit / setaudit / viewauditThe showaudit(8) and setaudit(8) commands display and specify information suc

Copyright © 2007, 2010, FUJITSU LIMITED. Tous droits réservés. Oracle et/ou ses sociétés affiliées ont fourni et vérifié des données techniques de cer

1-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20101.2.1 Major Differences Among the Server ModelsTABLE 1-1 shows the major differen

5-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010versionThe version(8) command displays the comprehensive firmware version (XCP ve

6-1CHAPTER6XSCF Mail FunctionThis chapter describes the XSCF mail function.6.1 Overview of XSCF Mail FunctionThe mail report function, used by XSCF fi

6-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 6-1 outlines the XSCF mail function.FIGURE 6-1 XSCF Mail FunctionXSCF Emai

Chapter 6 XSCF Mail Function 6-3Parts Fault NotificationXSCF monitors components (such as CPU modules, fan units, CPU/Memory Board unit) in the server

6-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Reply address (from specification)—(See setsmtp(8)) Recipient address for mail for

Chapter 6 XSCF Mail Function 6-56.3 Contents of Parts Fault NotificationThis section explains the contents of the email messages sent for parts faults

6-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 MSG-ID: Message ID. Use the message ID for accessing the specified URL to acquir

7-1CHAPTER7XSCF SNMP Agent FunctionThis chapter explains the XSCF SNMP agent function.7.1 Overview of the XSCF SNMP AgentXSCF supports the Simple Netw

7-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 7-1 shows an example of a network management environment using SNMP.FIGURE

Chapter 7 XSCF SNMP Agent Function 7-37.2 MIB Definition FileThe SNMP agent responds with management information from the MIB information to requests

Chapter 1 XSCF Overview 1-15FIGURE 1-4 Connections to XSCF (In the Midrange Servers)Note – In the systems with two XSCF Units, the XSCF Unit is in a

7-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The following shows data as an example of MIB management information.Note – This M

Chapter 7 XSCF SNMP Agent Function 7-57.3 About TrapWhen an event occurs, the SNMP agent function notifies the SNMP manager of the event. This functio

7-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010In the example above, the following items are displayed: agent-address: The IP ad

Chapter 7 XSCF SNMP Agent Function 7-7FIGURE 7-2 is a conceptual diagram of issuance of a Trap. FIGURE 7-2 Trap IssuanceTrap issuedSystemXSCFEvent re

7-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20107.4 Setting Up the XSCF SNMP Agent FunctionThis section explains how to set up the

Chapter 7 XSCF SNMP Agent Function 7-9 Host name of the trap destination Step 3: Enable the XSCF SNMP agent function. Enable one or both of the foll

7-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Performing User Management (USM Management) and Management of the Access Control

8-1CHAPTER8Upgrade of XSCF Firmware and MaintenanceThis chapter explains how to update the firmware and how to collect log data. 8.1 Update the XSCF F

8-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 8-1 is a conceptual diagram of the firmware update.FIGURE 8-1 Conceptual D

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-3Note – The OpenBoot PROM firmware is applied by a domain reboot. In the M3000 server, this funct

1-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010XSCF-LAN Ethernet ConnectionXSCF-LAN Ethernet enables workstations and PCs to con

8-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Firmware Update EnvironmentThe following environment is required for the firmware

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-58.1.4 Method of Checking the Firmware VersionThe firmware version for this system is called the

8-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20108.1.5 Three Steps of the Firmware UpdateThe firmware update for the server has thr

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-78.1.6 Features of XSCF Firmware UpdateThe firmware update that is managed by XSCF has the follow

8-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 8-1 describes the firmware update types and update times.Note – (1) Correspo

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-9Note – (2) The replacement of the XSCF Unit and the version matching is performed by FEs. When b

8-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 When a system board is moved to a domain by the DR function, the version on the

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-11Updating XCP From the Network File preparation:1. Download the XCP files from a public site to

8-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Confirm the XCP version. To confirm the XCP version, see the figure of a four-

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-13c. If complete message, "Download successful: ..." and "MD5: ..." are disp

Chapter 1 XSCF Overview 1-17Note – The serial port is used by maintenance engineers.Note – The two XSCF-LAN ports are used for the same purpose (alter

8-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – If the "XCP update requires all domains to be rebooted (Previous Open

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-15Note – The display might be different according to XCP version and system configuration.At this

8-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105. Confirm that the version of the system firmware that is running is that of the

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-17Note – In a system with redundant XSCF Units:i) Perform the firmware update in order, beginning

8-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20101. After a CMU/MBU addition or replacement task and an allocation to a domain hav

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-192. If the replacement unit and the replaced unit have different versions, a message is displaye

8-20 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Confirming That the XSCF Firmware Is Updated When the XSCF Unit Is Replaced (in a

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-218.1.11 If an Error Occurs During XSCF Firmware UpdateIf the system hangs or any of the messages

8-22 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20108.2 Collecting XSCF LogsLog information for the XSCF firmware is used for investi

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-23Logs Containing Fault InformationIf a failure occurs in the system, the system and XSCF collect

1-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 1-5 XSCF-LAN Redundancy (In Entry-level and Midrange Servers)In the confi

8-24 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Other LogsTABLE 8-4 outlines other logs collected for XSCF log information.TABLE

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-25Note – The table is read in the same way as TABLE 8-3. For examples of logs, see Appendix B.Not

8-26 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The following is the procedure for saving logs.Saving the Logs by Connecting the

Chapter 8 Upgrade of XSCF Firmware and Maintenance 8-273. Execute the data transfer. When the data transfer is complete, please contact authorized ser

8-28 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

9-1CHAPTER9How to Use the XSCF Web This chapter describes how to use the XSCF Web. 9.1 Overview of the XSCF WebThe XSCF Web uses https and the SSL/TLS

9-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-1 outlines each page.TABLE 9-1 XSCF Web Pages Basic Page DescriptionLogin

Chapter 9 How to Use the XSCF Web 9-3The following figures show examples of these pages in a web browser.FIGURE 9-1 shows an example of the Login page

9-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 9-2 shows an example of the Tree frame.FIGURE 9-2 Example of the Tree Fram

Chapter 9 How to Use the XSCF Web 9-5FIGURE 9-3 shows an example of the Tree frame and main page.FIGURE 9-3 Example of the Tree Frame and Main PageNo

Chapter 1 XSCF Overview 1-19FIGURE 1-6 Two XSCF-LANs and Two XSCF Units Configuration (In High-End Servers)For details on LAN configurations and conn

9-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20109.2.1 PrerequisitesSome settings are disabled in the initial settings of the XSCF

Chapter 9 How to Use the XSCF Web 9-79.2.4 Specifying the URLWhen specifying the URL, specify the IP address configured with XSCF or the XSCF host nam

9-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010changed. The authentication timeout is 10 minutes by default. The monitoring inter

Chapter 9 How to Use the XSCF Web 9-99.4 XSCF Web PagesThis section describes the configuration of pages available with the XSCF Web console.Menu and

9-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – Menu items may be changed to improve functionality. The menu displays show

Chapter 9 How to Use the XSCF Web 9-11Displaying System StatusTABLE 9-3 lists the functions for displaying the status of the entire system. Select [St

9-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-4 lists the functions for displaying the status of a domain. Select [Stat

Chapter 9 How to Use the XSCF Web 9-13System and Domain OperationTABLE 9-6 lists the function used for the system as a whole and individual domains. S

9-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-8 lists the functions used for System board configuration. Select [Operat

Chapter 9 How to Use the XSCF Web 9-15TABLE 9-9 lists the functions for the domain configuration. Select [Operation]-[Domain Configuration]-[Domain Co

1-20 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20101.3.2 NTP Configuration and Time SynchronizationThe system uses the XSCF Unit clo

9-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Setting SystemTABLE 9-10 lists the functions for the network configuration of XSC

Chapter 9 How to Use the XSCF Web 9-17Note – The [Current] and [Reserve] menus are supported in XCP1090 or later.Note – The DSCP link address cannot b

9-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-11 lists the functions for setting the XSCF time. Select [Settings]-[Time

Chapter 9 How to Use the XSCF Web 9-19TABLE 9-13 lists the functions for configuring LDAP. Select [Settings]-[LDAP] in the Menu tree.Note – In the set

9-20 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-14 lists the functions for configuring LDAP/SSL. Select [Settings]-[LDAP/

Chapter 9 How to Use the XSCF Web 9-21TABLE 9-15 lists the functions for configuring Active Directory. Select [Settings]-[Active Directory] in the Men

9-22 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-16 lists the functions for configuring XSCF user management. Select [Sett

Chapter 9 How to Use the XSCF Web 9-23TABLE 9-17 lists the functions for configuring XSCF audit. Select [Settings]-[Audit] in the Menu tree.TABLE 9-18

9-24 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 9-19 lists the functions for configuring XSCF mail. This page provides the

Chapter 9 How to Use the XSCF Web 9-25TABLE 9-21 lists the functions for configuring security access for SNMPv3. Select [Settings]-[SNMP Security] in

Chapter 1 XSCF Overview 1-21In the M8000/M9000 servers, a basic cabinet and an expansion cabinet contain one DVD drive/tape drive unit respectively, a

9-26 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010For COD settings and command information, see the COD User’s Guide and the XSCF R

Chapter 9 How to Use the XSCF Web 9-27TABLE 9-25 lists the functions for the firmware update. Select [Utility]-[Firmware Update] in the Menu tree.To s

9-28 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010LogsTABLE 9-26 lists the functions for referring and saving each log. Select [Log

Chapter 9 How to Use the XSCF Web 9-29Component InformationTo refer to the information and status of physical components in the server, select the tar

9-30 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20109.5 XSCF Web Error MessagesTABLE 9-27 lists the typical messages category from th

A-1APPENDIXAWarning and Information MessagesThis appendix explains the XSCF fault and informational messages output during the operation with the cons

A-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 Panic messageThis message is output in case of panic. The panic message is outpu

Appendix A Warning and Information Messages A-3A.2 Messages in Each FunctionThis section explains each Oracle Solaris OS and XSCF function by which th

A-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. The contents of notification or fault information can be confirmed by accessing

Appendix A Warning and Information Messages A-5Recognizing Status Notification or Fault Information in a Monitoring Message on the XSCF Shell Terminal

1-22 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Caution – IMPORTANT – To use the function as explained previously, you must creat

A-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

B-1APPENDIXBXSCF Log InformationThis appendix explains the following XSCF log information that can be referenced using the XSCF Shell showlogs(8) comm

B-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010The showlogs(8) error option displays fault information in a format specific to th

Appendix B XSCF Log Information B-3 Time at which each problem occurred (Occurred). This is indicated in local time. Replacement component (FRU) tha

B-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the message ID for accessing the specified URL to acquire detailed informat

Appendix B XSCF Log Information B-52. Use the message ID for accessing the specified URL to acquire detailed information corresponding to this problem

B-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 Type of power event that occurred (Event). The following lists each event and it

Appendix B XSCF Log Information B-7B.3 Event LogWhen an event occurs in the server, such as when the system status changes, the configuration is chang

B-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010B.4 Using the showlogs Command to Display Other LogsThis section explains how to r

Appendix B XSCF Log Information B-9B.4.3 Console LogUsing the showlogs(8) Command to Reference Console LogsThe XSCF firmware collects the domain conso

Chapter 1 XSCF Overview 1-23Note – Symbols: S: Supported. — : Not supported.1.4.1 User Accounts and User PrivilegesThe system administrator and field

B-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 IPL message (Message)B.5 Audit LogThis section explains how to reference the au

Appendix B XSCF Log Information B-11 Upriv TokenLabel, success/failure Udpriv TokenLabel, success/failure, privilege name, domain1, ... , domainN C

B-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 Shell commandHeaderSubjectCommandTextUpriv | UpdprivReturnNote – Some Tokens mi

Appendix B XSCF Log Information B-13Using the showldapssl(8) Command to Confirm the LDAP/SSL Log● Perform the showldapssl(8) command on the XSCF Shell

B-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

C-1APPENDIXCXSCF MIBThis appendix explains the XSCF Management Information Base (MIB), which is supported by the XSCF SNMP agent function.C.1 MIB Obje

C-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010udp OBJECT IDENTIFIER ::= { mib-2 7 }snmp OBJECT IDENTIFIER ::= { mib-2 11 }enterp

Appendix C XSCF MIB C-3C.2 Standard MIBThe standard MIB supported by the XSCF conforms to the following RFC (Note). For the standard MIB definition fi

C-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – In the M3000/M4000/M5000/M8000/M9000 servers, information has been added, s

Appendix C XSCF MIB C-511. scfIoBoxInfo groupThis group provides information for the External I/O Expansion Unit (IOBOX) that is attached to the syste

1-24 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – (@n) "@domain number" is added behind the privilege name for the

C-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

D-1APPENDIXDTroubleshootingThis chapter describes problems that can occur during use of the XSCF console or during the operation of the system and pro

D-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Could Not Connect to XSCF Through the Serial Port Check the connection between th

Appendix D Troubleshooting D-3Do Not Know the IP Address of XSCF Use the shownetwork(8) command to check the current network configuration. If it has

D-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010A Mail Report Was Not Received From XSCF XSCF does not necessarily report all eve

Appendix D Troubleshooting D-5Alert Message is Displayed in XSCF Web Please confirm the content of the security alert message and stop the use of XS

D-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010A. The processing flow before system startup is as follows:1. The operator turns o

Appendix D Troubleshooting D-7A. Error information reflected in the MIB file is the latest log data of XSCF.D.2 Troubleshooting the Server While XSCF

D-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 fmdumpIf you find an error, see Appendix B in this manual for the corrective act

E-1APPENDIXESoftware License ConditionsSome of the software functions explained in this manual are licensed under public licenses (GNU Public License

2-1CHAPTER2Setting Up XSCFThis chapter explains how to set up XSCF.2.1 XSCF Setup SummaryEach XSCF function must be configured before it can be used.

E-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010GNU GENERAL PUBLIC LICENSEVersion 2, June 1991 Copyright (C) 1989, 1991 Free Softw

Appendix E Software License Conditions E-3 6. Each time you redistribute the Program (or any work based on theProgram), the recipient automatically r

E-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 When we speak of free software, we are referring to freedom of use, notprice. O

Appendix E Software License Conditions E-5 3. You may opt to apply the terms of the ordinary GNU General PublicLicense instead of this License to a g

E-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010of software distributed through that system in reliance on consistentapplication o

Appendix E Software License Conditions E-7 * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must

E-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd

Appendix E Software License Conditions E-9 * * 1. Redistributions of source code must retain the above copyrightnotice, this * list of conditions and

E-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 201012) Miscellaneous. This License represents the complete agreementconcerning the s

Appendix E Software License Conditions E-11 6. Trademarks. This License does not grant permission to use the tradenames, trademarks, service marks,

2-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 DVD Drive/Tape Drive Unit Administration (optional) COD Administration (optiona

E-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010/* * Copyright (c) 1991 Bell Communications Research, Inc. (Bellcore) * * Permiss

Appendix E Software License Conditions E-132. Redistributions in binary form must reproduce all prior and currentcopyright notices, this list of condi

E-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010* Redistributions in binary form must reproduce the above copyrightnotice, this

Appendix E Software License Conditions E-15 [However, none of that term is relevant at this point in time. Allof these restrictively licenced soft

E-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 * * 2. Redistributions in binary form must reproduce the above copyright * not

Appendix E Software License Conditions E-17----/*- * Copyright (c) 1990 The Regents of the University of California. * All rights reserved. * * Redist

E-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDIN

Index-1IndexAAdding or deleting a user account and specifying a password, 2-39Administrationaltitude,2-185audit, 2-116https, 2-109locale, 2-184log arc

Index-2 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010network, 2-16system board, 2-170Configuring an NTP server, 2-95Configuring IP

Index-3LLDAP, 2-43, 2-48, 2-70Localesetting,2-184Locale Administration, 2-184Logaudit, B-10confirm the audit trail, B-10, B-12, B-13console, B-9event,

Chapter 2 Setting Up XSCF 2-3Note – Establish one-to-one communication between the PC and XSCF during the initial setup.1. Connect to XSCF by serial c

Index-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Security commands, 5-16Serverconfiguration,5-10, 5-12control, 5-10information

Index-5User privilegespecifying, 2-40USM management information, 2-137VVACM management information, 2-138WWeb server certificatecreating, 2-115importi

Index-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010

2-4 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Set the password policy.(This table includes the example of setting items and c

Chapter 2 Setting Up XSCF 2-5 When the system time is updated, the XSCF reset is done and the XSCF session is disconnected. Please log in again to th

2-6 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20107. Installing the user public key. Before using the SSH user key for an XSCF-LAN

Chapter 2 Setting Up XSCF 2-78. Configure the network. Perform the applynetwork(8) command to apply the network settings. To complete the network set

2-8 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Type the passphrase you have already set in the case that you would be using SSH w

Chapter 2 Setting Up XSCF 2-9This manual does not provide details on LDAP, Active Directory, and LDAP/SSL, so see the available LDAP, Active Directory

vContentsPreface xi1. XSCF Overview 1–11.1 XSCF Features 1–11.2 XSCF Functions 1–91.2.1 Major Differences Among the Server Models 1–141.3 Types of Con

2-10 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 201014. Configure the log archiving settings. 15. Configure the audit settings. Note

Chapter 2 Setting Up XSCF 2-1119. Configure the domain settings. In the M3000 server, you cannot perform operations such as setting the domain config

2-12 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 201021. Configure the Locale settings.22. Configure the Altitude Administration setti

Chapter 2 Setting Up XSCF 2-13Before attempting to establish a connection to the XSCF and log in from the web browser window of the XSCF Web, perform

2-14 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 201010. Establish a connection to XSCF and log in from a web browser. Specify the ho

Chapter 2 Setting Up XSCF 2-152.2 Specifying the XSCF SettingsThis section describes the XSCF settings in detail.XSCF settings can be made in the foll

2-16 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.1 Network ConfigurationNetwork Configuration is used to specify items relatin

Chapter 2 Setting Up XSCF 2-17TABLE 2-2 lists setting items and the corresponding shell commands.To complete the network settings, the XSCF reset is r

2-18 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Host name/domain nameSets a host name and a domain name for the XSCF Unit.FQDN ca

Chapter 2 Setting Up XSCF 2-19In systems with two XSCF Units, the two XSCF Units are connected by system internal ports, which are the RS-232C (serial

vi SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.3 LDAP Administration 2–432.2.4 Active Directory Administration 2–482.2.5 LDAP/

2-20 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010FIGURE 2-1 shows the network interface which is required for the XSCF and domain

Chapter 2 Setting Up XSCF 2-21XSCF network configuration procedure and the referenceThe procedure to set up the XSCF network is as follows. Each step

2-22 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010To make the IP address redundant, specify the same subnet address to the LAN port

Chapter 2 Setting Up XSCF 2-235. Specify the host name, routing, and DNS. In the M8000/M9000 servers, subsequently to the XSCFU#0 side, specify the ho

2-24 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling the XSCF Network and Specifying an IP Address and Netmask f

Chapter 2 Setting Up XSCF 2-252. Use the showdscp(8) command to display DSCP information.3. Use the setnetwork(8) command to specify network interface

2-26 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20104. Use the setdscp(8) command (see Note) to specify network interface information

Chapter 2 Setting Up XSCF 2-27This is because the DSCP communication protocol, PPP (Point to Point Protocol), does not notify the netmask value specif

2-28 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Configuring XSCF RoutingIn a redundant XSCF unit configuration, the following are

Chapter 2 Setting Up XSCF 2-292. Use the setroute(8) command to specify the routing environment for a network interface.Making XSCF DNS Settings Comm

Contents vii3.2.1 Connecting XSCF via the XSCF-LAN Port Or the Serial Port 3–113.2.2 XSCF-LAN and Serial Connection Purposes 3–154. Operation of the S

2-30 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setnameserver(8) command to specify the name server and the search pat

Chapter 2 Setting Up XSCF 2-31Configuring IP Packet Filtering Rules for XSCF Network Command operation1. Use the showpacketfilters(8) command to disp

2-32 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010<Example 1> Permit the IP address 192.168.100.0/255.255.255.0 to go through

Chapter 2 Setting Up XSCF 2-33Note – You can set the IP filtering rules to the input packets, not to the output packets.Applying the XSCF Network Sett

2-34 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010 At this time, the window session is disconnected, so please reconnect to the XS

Chapter 2 Setting Up XSCF 2-353. Use the traceroute(8) command to confirm the network path to network devices.Note – The confirming functions of the X

2-36 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 2-4 lists setting items and the corresponding shell commands.TABLE 2-4 Use

Chapter 2 Setting Up XSCF 2-37Password policy Sets a password policy as described below.• Minimum number of days that must elapse before the password

2-38 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Note – (1) If the password policy is set, then the password policy is applied to

Chapter 2 Setting Up XSCF 2-39Adding or Deleting a User Account and Specifying a Password Command operation1. Use the showuser(8) command to display

viii SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20105. Overview of the XSCF Shell 5–15.1 Overview of the XSCF Command Shell 5–15.2 Lo

2-40 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the password(8) command to specify a password.Specifying a User Privilege

Chapter 2 Setting Up XSCF 2-413. Use the showuser(8) command to confirm the privilege.Enabling or Disabling a User Account Command operation1. Use th

2-42 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setpasswordpolicy(8) command to specify a password policy.3. Use the s

Chapter 2 Setting Up XSCF 2-432.2.3 LDAP AdministrationLDAP administration is used to specify items relating to LDAP clients. The LDAP server, bind ID

2-44 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010TABLE 2-6 lists setting items and the corresponding shell commands:TABLE 2-6 LDA

Chapter 2 Setting Up XSCF 2-45Note – PEM: Abbreviation for Privacy Enhanced Mail. Mail to be sent is encrypted for increased privacy.Enabling or Disab

2-46 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102. Use the setldap(8) command to configure an LDAP client.3. Use the showldap(8)

Chapter 2 Setting Up XSCF 2-473. Use the showldap(8) command to confirm that you have imported the certificate chain.Testing a Connection to an LDAP S

2-48 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20102.2.4 Active Directory AdministrationActive Directory administration is used to s

Chapter 2 Setting Up XSCF 2-49Directory server. Each group has privileges associated with it which are configured on the XSCF. A user’s group membersh

Contents ix8.1.2 Firmware Update Conditions and Environment 8–38.1.3 Method of Delivering Firmware 8–48.1.4 Method of Checking the Firmware Version 8–

2-50 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enable/disable strictcertmodeEnables or disables the strictcertmode.If strictcert

Chapter 2 Setting Up XSCF 2-51Before Active Directory settingsNote the following before settings: Active Directory is supported in XCP1091 or later.

2-52 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling the Active Directory Server Command operation1. Use the sh

Chapter 2 Setting Up XSCF 2-53Specifying an Active Directory Server and Port Number Command operation1. Use the showad(8) command to display Active

2-54 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 20103. Use the showad(8) command to confirm the Active Directory server setting.Enabl

Chapter 2 Setting Up XSCF 2-553. Use the showad(8) command to confirm the DNS locator mode status.Configuring the DNS locator Query Command operation

2-56 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Enabling or Disabling the Expanded Search Mode Command operation1. Use the showa

Chapter 2 Setting Up XSCF 2-572. Use the setad(8) command to enable or disable the strictcertmode.3. Use the showad(8) command to confirm the strictce

2-58 SPARC Enterprise Mx000 Servers XSCF User’s Guide • December 2010Loading or Deleting the Server Certificate Command operation1. Use the showad(8)

Chapter 2 Setting Up XSCF 2-592. Use the setad(8) command to load the server certificate to the XSCF.<Example1> Loads a server certificate for t